|
Do you need to drill holes into expensive porcelain tiles |
|
We provide an excellent drilling system to drill into tiles
 |
The kit contains these very useful sizes
2x 6mm, 2x 8mm, 16mm, 30mm and 40mm
And a drill guide to hold the drill steady on the work surface.
The system is really easy to use. Just follow these instructions
1: To make a hole such as this just do the following
2: Place the drill plate or guide onto the porcelain tile. Or on the granite. Spray with some water.
3: Put the drill into the guide. It will not slip. Start the drill at a slow speed. Begin to make the hole
4:Remove the plate. It is no longer needed. The drill will sit in the groove you just cut. Spray with water to cool.
5: After about 3 minutes in time a perfect hole will form into the surface. Easy !
|
Diamond drills MUST be used with
an anti-slip drill plate as shown below
|
||||
|
Why? Because Without a non-slip plate the cores will skid and scratch your expensive tiles. Why risk it ? |
 |
||
|
Our competitors charge hundreds of pounds for their arbor and center pilot drilling rigs. We removed "centre pilots" to bring you three benefits. A Centre pilots are expensive costing over £20 each to replace. By removing them we dramatically reduced drilling costs for you !
B Centre pilots are only made of carbide steel not diamond. To work they must be kept cool with a continuous supply of water pumped via an arbor and water bottle. Removing them eliminated these bulky extra items saving you even more money, cutting down on water consumption and cutting down on clutter. Remember the reason our competitors must continuously pump water to the drill site is because their pilots are made of carbide not diamond.
No need to continuously pump water!
C Another benefit is safety. You may not be aware of items behind the tile such as a water pipe or electrical cable. Using pilot drills it is possible to accidently pierce them. With our system you do not penetrate any further than the tile because you are grinding not drilling.
How does the 365drill system work?
If you think about it, pre-drilling a centre hole was always a waste of your energy and money. So we resolved the guidance problem in a special way. Our drill plate firmly holds the crown from the outside not the inside. This breakthrough - developed exclusively by us - puts the diamond crown into direct contact with the drilling surface so only the portion of tile being drilling is removed and nothing else. No center pilot = Low costs for you | Efficient drilling less water | Wont pierce hidden items Developed by 365Drills * PATENT APPLICATION 0601484.9 * |
||||
To provide you with the best solution we ensure our diamonds are the highest quality. We also take care to ensure our crown walls are ultra thin. Ultra thin walls are designed to ensure rapid penetration into the tile. We are providers of the best value diamond drilling kits but not cheap diamond drills. You will find cheaper drills with less diamonds but we have a branded product with a reputation to uphold.
| Caution: Do not confuse our crows with "diamond brick drills". Those drills (see an example below) might look "beefier" because there is more metal - but to drill into tile you actually want more diamond and less metal. Remember its diamond doing the work not metal. Metal actually gets in the way getting hot. When it gets hot it releases the diamonds. |
 |
| Examine the diamond drill with the green tick. This is our own porcelain tile drill placed next to a brick drill and can be identified because of the ultra thin wall designed to penetrate hard material. In contrast the sturdier looking drills have more metal surface area but less diamond. We are often asked by customers to supply thicker drills for porcelain work. But thick drills with low diamond content do not work in porcelain, granite or glass - only bricks. Thicker drills for porcelain do exist but they have a high diamond content and cost many hundreds of pounds. If in any doubt when comparing our brand to alternatives please look for the statement "porcelain tile drill" to be sure you are selecting the right product. |
We are selling a complete diamond drilling solution at just £40 (more detail below)
* AMAZING VALUE *
You probably paid hundreds of pounds for your tiles so please don't risk cutting corners on diamond quality or kit solutions.
We are able to provide full technical backup and are only a phone call or e-mail away.
TECHNICAL HELP LINE 0870 061 7593
or 0777 366 4519 (mobile)
SALES HELP LINE 0208 816 7937
email - info@365drills.com
OUR GUARANTEE AND PROMISE TO YOU
If you are not FULLY satisfied with our product we will refund you in full.
Before comitting to buy see what others - just like you - say about us and our products here in live feedback
We developed this technology ourselves. Beware of copycats trying to steal our brand. Our lawyers are watching!
|
Further tips, projects
and info at our main website
|
 |